Piwi diagnostic program for Porche Taykan

[carlos vilarinho]

The last link is on a Google Drive and is downloading with good speed.

I also downloaded this Acronis file and I don't think it has anything to do with Piwi…,I see that you did it too, what did you get into…???,

Sponsored

 

[Shug]

This is an Acronis image with all the PIWIS files installed.

It is the same as the $13 files you paid for.

Both should install without issue.

 

[carlos vilarinho]

This is an Acronis image with all the PIWIS files installed.

It is the same as the $13 files you paid for.

Both should install without issue.

Hi Shug, as I told you before, I bought the Piwi that you sent me for £9. I already have the files in rar on my computer and I'm extracting them one by one to the computer, and then I have to see how to install all this! Another thing I wanted to ask you, I disconnected the 800v battery and the 12v battery, when I disconnected it at the switch, the 800v battery only had 3% charge, the car is out here, I think there will be no problem for the 800v battery to be off for a period of time….

 

[Shug]

Good luck unpacking the software.

I have seen warnings about the 800V battery needing to be 20% charged and also using the 12V charger that we previously discussed.

Suggest that you organise something to keep at least one of the batteries charged since you may do more harm than good if things go wrong.

 

[carlos vilarinho]

Hi Shug, as I told you before, I bought the Piwi that you sent me for £9. I already have the files in rar on my computer and I'm extracting them one by one to the computer, and then I have to see how to install all this! Another thing I wanted to ask you, I disconnected the 800v battery and the 12v battery, when I disconnected it at the switch, the 800v battery only had 3% charge, the car is out here, I think there will be no problem for the 800v battery to be off for a period of time….

So you advises me to reconnect the safety switch to the 800V battery as soon as possible and charge the battery. When I removed the negative terminal, the 12v battery had sufficient charge, the 800v battery only had 3% and I was advised to preserve both since I was going to work on the car that turns off the safety switch of the 800v battery and the terminal from 12 v

 

[carlos vilarinho]

As I mentioned before, after finding out what is wrong and fixing it, my car has two battery recalls to do.

 

[Shug]

If you now have an 800v battery charger, I suggest that you charge your 800V battery to at least 20% in preparation for working with PIWIS.

The 800V battery recall is not something you need to consider at this time.

 

[carlos vilarinho]

If you now have an 800v battery charger, I suggest that you charge your 800V battery to at least 20% in preparation for working with PIWIS.

The 800V battery recall is not something you need to consider at this time.

I will have the charger in the morning and I will put everything back in the car inside and as soon as the charger arrives I will reconnect the safety switch and the 12v battery and then charge the car above 20%, I ended up buying this charger because In addition to seeming like a better option than the original, it has an LED display with charging information and is a universal type 2 charger.

 

[carlos vilarinho]

Another thing I would like to share with you, as you know the display in my car indicates a lack of brakes, i.e. brake pads, ABS, etc. The other day, when I spoke to the Porsche dealer in Belgium, I was informed that the car had never been serviced there. to change the brake pads because the car has about 70.000 km…….this morning when looking at the disc brake on the front right wheel I noticed that the disc is a little scratched as you can see in the photos, I think I will have it later I remove these brake pads and put new ones, and sensors, I put the car in lift mode and remove the wheels one by one and touch these brake pads

 

[Shug]

I believe that 80% is the maximum charge that you should use on the 800V battery until you can have the battery recall completed.


Suggest you connect the 12V battery first, then the 800V battery.

Did you check all the fuses above the 12V battery, if not, I suggest you do that before the above.

 

[carlos vilarinho]

I believe that 80% is the maximum charge that you should use on the 800V battery until you can have the battery recall completed.


Suggest you connect the 12V battery first, then the 800V battery.

Did you check all the fuses above the 12V battery, if not, I suggest you do that before the above.

Shug, when I finally have my car fixed, I would like to make a point of thanking you in some way for all the time and availability you have given to help me fix this car…!

 

[Shug]

No worries Carlos.

I am happy to help.

There are others that have been very helpful too,

The software is not easy to use, the other experts will be able to chime in to help.

 

[carlos vilarinho]

Can someone here tell me step by step what I need to do or install so that I can install piwi 3 41,500+ 38,250 developer+coding (VMWARE) on my computer with Windows 10…! Honestly, I've never installed any piwi before and when I looked at these files, I already unzipped (winrar) I don't know what the next steps will be

 

[Shug]

All the information you need to install the software is in the link I posted earlier:-

A PIWIS 3 for only $75 - Rennlist - Porsche Discussion Forums

 

[carlos vilarinho]

All the information you need to install the software is in the link I posted earlier:-

A PIWIS 3 for only $75 - Rennlist - Porsche Discussion Forums

I apologize and thank you at the same time because I didn't remember... you had already sent this to me before ?ok I will follow the instructions and try to install it if I have any difficulties I present it here, thank you again

Sponsored