Anyone with PIWIS?

[bigkraig]

maybe one of these?

MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_off_1: 30
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_off_2: 60
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_standby: 31
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_pdd: 10
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_pdd_online_update: 20
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_standby_pwr_save: 60
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_shutdown_suspend: 120
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_sleep: 10080
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_on_tel: 60
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_on_online_swdl: 600
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_online_uota: 60
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_online_delay: 4320
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_bem_shutdown: 10
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_max_cluster_wakeup: 240
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_rtc: 60
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: maxCarWakeup: 100
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: maxUnitWakeup: 10
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: maxRTCWakeup: 100
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_dci: 120
MU_TI_001010 >> Control unit, coding >> powermanagement_timer: t_mmi_online_min: 120

Sponsored

 

[Elysium]

I don't believe this one has been mentioned yet. If you have surround view but not 3D surround view:

ZFAS AU516 003 -> Kodierwert -> Bitfield (5) TV_3D_Presentation

Change from "off" to "on"

 

[Chiu]

Do all these codes require PPN? Or can they be modified as long as they have PIWIS?

 

[Elysium]

Do all these codes require PPN? Or can they be modified as long as they have PIWIS?

They do not require PPN, just PIWIS 3 with engineering mode.

 

[Chiu]

They do not require PPN, just PIWIS 3 with engineering mode.

That's awesome, thanks! I've been thinking about buying a clone PIWIS 3 recently to adjust the configurations.

 

[Elysium]

That's awesome, thanks! I've been thinking about buying a clone PIWIS 3 recently to adjust the configurations.

I'd check out this guide, it is very helpful if you're just getting started. I'm using a PT3G instead of a VAS 6154 clone but the install steps are still the same.

 

[Chiu]

I'd check out this guide, it is very helpful if you're just getting started. I'm using a PT3G instead of a VAS 6154 clone but the install steps are still the same.

Thank you, superhero! I thought PIWIS could only run on a specific notebook, but it turns out it can be installed manually, just like how I used to code BMW with E-sys.

 

[Porsche-Guru]

I don't believe this one has been mentioned yet. If you have surround view but not 3D surround view:

ZFAS AU516 003 -> Kodierwert -> Bitfield (5) TV_3D_Presentation

Change from "off" to "on"

@Elysium
Could you please explain what 3D surround is compared to normal 3D?

Screenshots or some more detail please…. Thanks.

 

[Elysium]

@Elysium
Could you please explain what 3D surround is compared to normal 3D?

Screenshots or some more detail please…. Thanks.

I don't have any pictures at the moment but this post shows 3D surround view:
https://www.taycanforum.com/forum/threads/3d-surround-view-vs-surround-view.14432/post-217619

 

[Porsche-Guru]

I don't have any pictures at the moment but this post shows 3D surround view:
https://www.taycanforum.com/forum/threads/3d-surround-view-vs-surround-view.14432/post-217619

Thanks….

 

[mystermykee]

I don't have rear cross traffic alert. I'm not sure if that is only available with Innodrive. Anyway, if you have LCA you can enable rear cross traffic alert as it uses the same sensors.

Caveat: I'm not sure if it actually works since I usually park rear end first, so I haven't had a chance to test it. However, I did code it on my wife's 9Y0 Cayenne and the parking/back up camera mode notified of oncoming cross traffic while reversing

Taken from Cayenne coding on Rennlist.

Rear Radar S1 (Lane Assist Right) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA
Rear Radar S2 (Lane Assist Left) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA
ZFAS (Assist) Kodierwert: Bitfield (3) FW_RCTA : installed
PSM (ESP) Kodierwert: Byte 12 Rear Cross Traffic Alert : ja / an

I can't remember exactly what the modules in the Taycan are called for Rear Radar S1/S2, but they are something along the lines of "...VR...". But if you select those and go into manual coding, you'll see Radar S1/S2 listed. If I get into PIWIS again I'll remember to take note lol.

 

[Porsche-Guru]

I don't have rear cross traffic alert. I'm not sure if that is only available with Innodrive. Anyway, if you have LCA you can enable rear cross traffic alert as it uses the same sensors.

Caveat: I'm not sure if it actually works since I usually park rear end first, so I haven't had a chance to test it. However, I did code it on my wife's 9Y0 Cayenne and the parking/back up camera mode notified of oncoming cross traffic while reversing

Taken from Cayenne coding on Rennlist.

Rear Radar S1 (Lane Assist Right) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA
Rear Radar S2 (Lane Assist Left) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA
ZFAS (Assist) Kodierwert: Bitfield (3) FW_RCTA : installed
PSM (ESP) Kodierwert: Byte 12 Rear Cross Traffic Alert : ja / an

I can't remember exactly what the modules in the Taycan are called for Rear Radar S1/S2, but they are something along the lines of "...VR...". But if you select those and go into manual coding, you'll see Radar S1/S2 listed. If I get into PIWIS again I'll remember to take note lol.

Would much appreciate if you could find the actual module names in the Taycan. Thanks.

 

[Elysium]

Would much appreciate if you could find the actual module names in the Taycan. Thanks.

MRR_HR (Radar HR) -> Rear Radar S1 (Lane Assist Right) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA

MRR_HL (Radar HL) -> Rear Radar S2 (Lane Assist Left) Kodierwert: Bitfield Rear_Cross_Traffic_Alert : with_RCTA

ZFAS (Zentrales Fahrer Assistenz System) -> ZFAS (Assist) Kodierwert: Bitfield (3) FW_RCTA : installed

ESP (Bremsensteuergeraet)-> PSM (ESP) Kodierwert: Byte 12 Rear Cross Traffic Alert : ja / an

 

[Taycan4S_UK]

You know what would be a game changer?
Ability launch Android auto on passenger display.

I can then have CarPlay on driver display and Android AI box to load Android auto on passenger for Netflix

 

[Chiu]

Change from Distance 3 (Default) to 1

ACC->Kodierwert->CarMenu_distance_basic_setting -> Distance 1

Sponsored